• Building 3 Shunheli Industrial Park,
  • Lunjiao Shunde Foshan City Guandong China.
  • Working Hours
  • Mon – Sat Day: 09.00 To 18.00
Find Advisor
wehomachinery
The practice of wood clamp | Wood Sheet Clamp Carrier

The practice of wood clamp | Wood Sheet Clamp Carrier
03 Dec 2021

Material tools: 3mm thick balsa wood strips, utility knife, pencil, ruler, scissors, dental floss, flower pot with protruding edge at the opening, spray paint can, super glue or white glue. step: 1. Measure the size of the flowerpot to determine the size of the bracket we want to make. Spray the color you like on the flowerpot and let it sit to dry. 2. Each bracket needs 8 small wooden slats, the length is equal
Trouble with the wood saw | Wood Panel Saw

Trouble with the wood saw | Wood Panel Saw
03 Dec 2021

1. When the wood saw is refueling and stalling, working less vigorously, and the heating machine is overheated, it is generally a filter problem. Therefore, the filter should be inspected before work. A clean and qualified filter should be pointed at the sun to observe it. It should be thorough and bright. Otherwise, it is unqualified. When the filter of the chain saw is not clean enough, it should be washed with hot
Common failure causes of Wood Round Rod Making Machine and how to eliminate them

Common failure causes of Wood Round Rod Making Machine and how to eliminate them
03 Dec 2021

In the production process of charcoal rod making machine, the use of rod making machine directly affects the quality of machine-made charcoal, so the safe and efficient use of charcoal rod making machine is the primary condition. Mechanisms’ common postings and solutions for charcoal machine equipment: 1. The reason why the power indicator of the console is not bright: a. Connect the power supply of the mecha
Incorrect turning pitch and its solution | Wood Turning Machine

Incorrect turning pitch and its solution | Wood Turning Machine
03 Dec 2021

Fault analysis: the thread is incorrect in full length or partly, the pitch is uneven on the full length of the thread, or the slub pattern appears on the thread. Solution: 1. The overall length of the thread is incorrect: the reason is improper matching of the change wheel or the wrong position of the feed box handle. You can recheck the position of the feed box handle or check the hanging wheel. 2. Partially incorr
The use and characteristics of the direct supply of the double-head saw cutting machine | Automatic Double End Saw

The use and characteristics of the direct supply of the double-head saw cutting machine | Automatic Double End Saw
17 Nov 2021

The use and characteristics of the direct supply of the double-head saw cutting machine: The key to the CNC lathe consists of a protective cover, a material pressing device, a feeding device, a tool spindle power head, a cutting device, a fully automatic oil injection water cooling and moisturizing device, a sound card rack, a support rack, a pneumatic system, and household appliances system software, etc. The key pa
What is the reason why the saw beam does not rise when the band saw machine is cutting？ | Industrial Beam Saw

What is the reason why the saw beam does not rise when the band saw machine is cutting？ | Industrial Beam Saw
17 Nov 2021

1. First check if the bottom dead point contact switch is in good condition; 2. Whether the hydraulic oil tank is short of oil (after the hydraulic pump enters the air, it will cause damage to the oil pump or fail to reach the working hydraulic pressure); 3. Check whether the hydraulic oil pump is in good condition (the hydraulic pump of the sawing machine that has been used for a long time may not reach the hydrauli
What are the characteristics of a Dual Side Grinder? What is the difference between a Dual Side Grinder and a single-sided grinder

What are the characteristics of a Dual Side Grinder? What is the difference between a Dual Side Grinder and a single-sided grinder
17 Nov 2021

What are the characteristics of a double-sided grinder 　　 1. It is controlled by a stepless speed regulation system, which can easily adjust the grinding speed suitable for grinding various parts. Adopt electric-pneumatic proportional valve closed-loop feedback pressure control, which can independently control the pressure device. The upper plate is equipped with a slow-down function, which effectively prevents
The cause and treatment of Horizontal Bandsaw Mill failure

The cause and treatment of Horizontal Bandsaw Mill failure
17 Nov 2021

Features of horizontal band saw: Humanized operation interface, numerical control thickness display, fast and accurate adjustment of saw blade position. The hydraulic saw blade tension automatic compensation system ensures that the saw blade is always in the best tension state and prolongs the service life of the saw blade. One-time clamping, able to cut the wood. Pay attention to the following issues when using hor
Advantages and applications of Cross Cutting Saw Machine

Advantages and applications of Cross Cutting Saw Machine
09 Oct 2021

The application of the cross-cutting saw has brought great convenience to the paper cutting work, and the precise design of the computerized cross-cutting machine makes the cutting operation more time-saving and labor-saving. Cross-cutting saws are divided into mechanical cross-cutting machines and computerized cross-cutting machines due to different transmission control methods. The computerized cross-cutting machin